Amine-functionalized sorbents are promising materials for direct air capture (DAC). Reduced graphene oxide (rGO) aerogels have higher electrical and heat conductivities than commonly studied aminated silica. These properties could jointly enhance the productivity of an associated CO2 separation process. In this study, three-dimensional (3D) rGO aerogels were fabricated, modified with polyethyleneimine (PEI) at various mass ratios, and applied successfully as a CO2 adsorbent at different temperatures and pressures. The structure, morphology, and chemical properties of the aminated composite aerogels based on PEI-rGO were comparably characterized using elemental analysis, thermogravimetric analysis, and scanning electron microscopy. The CO2 uptake performance of the PEI-rGO aerogels was assessed by analysis of the adsorption isotherms at 20 and 50 °C. The optimized PEI-rGO-71 (referring to 71 wt% PEI to the sample) exhibited the highest CO2 uptake across the tested CO2 pressure range (0.03–101 kPa), reaching 0.61 mmol CO2/g at the partial pressure of CO2 in ambient air (0.04 kPa). It showed a superior CO2 capture capacity compared to previously reported amine-modified graphene-based sorbents at ambient CO2 concentration

A single coating formulation for multifunctional composites, such as a gas barrier against both oxygen and water vapour, is the holy grail for the packaging industry. Since the last decade, graphene has been touted as the ideal barrier material in composites due to its morphology and impermeability to all gases. However, this prospect is limited by either poor dispersion of graphene or excess surfactants to aid the dispersion, both leading to shortcuts that allow gas permeation through the composite. Here, we demonstrate a combined gas barrier with starch-graphene composite films made from a single formulation of surfactant-free starch nanoparticle-stabilized graphene dispersion (2.97 mg mL−1). Hence, the incorporated graphene reduces the permeability of both the oxygen and the water vapour by over 70% under all the relative humidity conditions tested. Moreover, these films are foldable and electrically conductive (9.5 S m−1). Our surfactant-free approach of incorporating graphene into an industrially important biopolymer is highly relevant to the packaging industry, thus offering cost-effective and water-based solution depositions of multifunctional composite films for wide-ranging applications, such as gas barriers in food packaging. © 2022, The Author(s).

A general formulation engineering method is adopted in this study to produce a highly concentrated (≈3 mg mL−1) inkjet printable starch–graphene ink in aqueous media. Photonic annealing of the starch–graphene ink is validated for rapid post-processing of printed films. The experimental results demonstrate the role of starch as dispersing agent for graphene in water and photonic pulse energy in enhancing the electrical properties of the printed graphene patterns, thus leading to an electrical conductivity of ≈2.4 × 104 S m−1. The curing mechanism is discussed based on systematic material studies. The eco-friendly and cost-efficient approach presented in this work is of technical potential for the scalable production and integration of conductive graphene inks for widespread applications in printed and flexible electronics. 

Attention to graphene dispersions in water with the aid of natural polymers is increasing with improved awareness of sustainability. However, the function of biopolymers that can act as dispersing agents in graphene dispersions is not well understood. In particular, the use of starch to disperse pristine graphene materials deserves further investigation. Here, we report the processing conditions of aqueous graphene dispersions using unmodified starch. We have found that the graphene content of the starch-graphene dispersion is dependent on the starch fraction. The starch-graphene sheets are few-layer graphene with a lateral size of 3.2 μm. Furthermore, topographical images of these starch-graphene sheets confirm the adsorption of starch nanoparticles with a height around 5 nm on the graphene surface. The adsorbed starch nanoparticles are ascribed to extend the storage time of the starch-graphene dispersion up to 1 month compared to spontaneous aggregation in a nonstabilized graphene dispersion without starch. Moreover, the ability to retain water by starch is reduced in the presence of graphene, likely due to environmental changes in the hydroxyl groups responsible for starch-water interactions. These findings demonstrate that starch can disperse graphene with a low oxygen content in water. The aqueous starch-graphene dispersion provides tremendous opportunities for environmental-friendly packaging applications. © 2021 American Chemical Society.

In this study, we have taken the concept of water treatment by functionalized magnetic particles one step forward by integrating the technology into a complete proof of concept, which included the preparation of surface modified beads, their use as highly selective absorbents for heavy metals ions (Zinc, Nickel), and their performance in terms of magnetic separation. The separation characteristics were studied both through experiments and by simulations. The data gathered from these experimental works enabled the elaboration of various scenarios for Life Cycle Analysis (LCA). The LCA showed that the environmental impact of the system is highly dependent on the recovery rate of the magnetic particles. The absolute impact on climate change varied significantly among the scenarios studied and the recovery rates. The results support the hypothesis that chelation specificity, magnetic separation and bead recovery should be optimized to specific targets and applications. 

A fundamental understanding of the interaction between graphene and a stabilizer is needed for the development of stable aqueous graphene dispersions. Here, we studied the interaction of graphene with the FMN in water. The UV-vis absorption spectra revealed blue shifts of the FMN absorption bands II (374 nm) and I (445 nm) in the presence of graphene. Furthermore, Fourier transform IR anal. showed that the graphene also upshifted the FMN vibration modes C10a=N1 and C4a=N5, which correspond to the FMN isoalloxazine binding sites N(1) and N(5), resp. In addition, thermogravimetric anal. showed that the thermal stability of graphene was enhanced by the adsorbed FMN, which supports the strong interaction. These results confirm that FMN adsorbs on the graphene surface in parallel conformation and hinders hydrogen bonding at the FMN isoalloxazine binding sites.

The assembly of magnetic cores into regular structures may notably influence the properties displayed by a magnetic colloid. Here, key synthesis parameters driving the self-assembly process capable of organizing colloidal magnetic cores into highly regular and reproducible multi-core nanoparticles are determined. In addition, a self-consistent picture that explains the collective magnetic properties exhibited by these complex assemblies is achieved through structural, colloidal, and magnetic means. For this purpose, different strategies to obtain flower-shaped iron oxide assemblies in the size range 25–100 nm are examined. The routes are based on the partial oxidation of Fe(OH)2, polyol-mediated synthesis or the reduction of iron acetylacetonate. The nanoparticles are functionalized either with dextran, citric acid, or alternatively embedded in polystyrene and their long-term stability is assessed. The core size is measured, calculated, and modeled using both structural and magnetic means, while the Debye model and multi-core extended model are used to study interparticle interactions. This is the first step toward standardized protocols of synthesis and characterization of flower-shaped nanoparticles.

Poly-3-hexylthiophene (P3HT) nanofibers are semiconducting high-aspect ratio nanostructures with anisotropic absorption and birefringence properties found at different regions of the optical spectrum. In addition, P3HT nanofibers possess an ability to be aligned by an external electric field, while being dispersed in a liquid. In this manuscript we show that such collective ordering of nanofibers, similar to liquid crystal material, significantly changes the properties of transmitted light. With a specially fabricated opto-fluidic component, we monitored the phase and transmission modulation of light propagating through the solution of P3HT nanofibers, being placed in the electric field with strength up to 0.1 V/μm. This report describes a technique for light modulation, which can be implemented in optical fiber-based devices or on-chip integrated components.

The structural and magnetic properties of magnetic multi-core particles were determined by numerical inversion of small angle scattering and isothermal magnetisation data. The investigated particles consist of iron oxide nanoparticle cores (9 nm) embedded in poly(styrene) spheres (160 nm). A thorough physical characterisation of the particles included transmission electron microscopy, X-ray diffraction and asymmetrical flow field-flow fractionation. Their structure was ultimately disclosed by an indirect Fourier transform of static light scattering, small angle X-ray scattering and small angle neutron scattering data of the colloidal dispersion. The extracted pair distance distribution functions clearly indicated that the cores were mostly accumulated in the outer surface layers of the poly(styrene) spheres. To investigate the magnetic properties, the isothermal magnetisation curves of the multi-core particles (immobilised and dispersed in water) were analysed. The study stands out by applying the same numerical approach to extract the apparent moment distributions of the particles as for the indirect Fourier transform. It could be shown that the main peak of the apparent moment distributions correlated to the expected intrinsic moment distribution of the cores. Additional peaks were observed which signaled deviations of the isothermal magnetisation behavior from the non-interacting case, indicating weak dipolar interactions.