Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Influence of peat addition to woody biomass pellets on slagging characteristics during combustion
Luleå University of Technology, Sweden.
Umeå University, Sweden.
RISE, SP – Sveriges Tekniska Forskningsinstitut, SP Energy Technology Center.
SLU Swedish University of Agricultural Sciences, Sweden.
Show others and affiliations
2013 (English)In: Energy & Fuels, ISSN 0887-0624, E-ISSN 1520-5029, Vol. 27, no 7, p. 3997-4006Article in journal (Refereed) Published
Abstract [en]

Upgraded biofuels such as pellets, briquettes, and powder are today commonly used in small as well as large scale appliances. In order to cover an increasing fuel demand new materials such as bark, whole tree assortments, and peat are introduced. These materials have higher ash content which is why they are potentially more problematic compared with stem wood. In general, few studies can be found regarding cocombustion of peat and biomass and in particular where the slagging tendencies are discussed. The overall objective of this study was therefore to determine the influence of peat addition to woody biomass pellets on slagging characteristics. Two different peat assortments (peat A and B) were copelletized separately in four different dry matter levels (0-5-15-30 wt %) into stem wood and energy wood, respectively. Peat A was a traditional Scandinavian fuel peat, with a high ash and Si content (carex), and peat B had a low ash content and relatively high Ca/Si ratio (sphagnum) chosen for its special characteristics. The produced pellets were combusted in a commercial underfed pellet burner (15 kW) installed in a reference boiler. The collected deposits (bottom ash and slag) from the combustion experiments were chemically characterized by scanning electron microscopy (SEM) combined with energy-dispersive X-ray analysis (EDS) and X-ray diffraction (XRD) regarding the elemental distribution and morphology and phase composition, respectively. In addition, the bottom ashes were characterized according to inductively coupled plasma atomic emission spectroscopy (ICP-AES). To interpret the experimental findings chemical equilibrium model calculations were performed. The slagging tendency increased when adding peat into the woody biomasses. Especially sawdust with its relatively low ash and Ca content was generally more sensitive for the different peat assortments. Cofiring with the relatively Si and ash rich peat A resulted in the most severe slagging tendency. A significant increment of the Si, Al, and Fe content and a significant decrement of the Ca content in the slag could be seen when increasing the content of peat A in both woody biomasses. The slagging tendency increased when adding peat A because high temperature melting Ca-Mg oxides react to form more low temperature melting Ca/Mg-Al-K silicates. The slagging tendency was significantly lower when adding the more ash poor peat B, with relatively high Ca/Si ratio, into the woody biomass fuels compared with the peat A mixtures. The slag from the peat B mixings had a slightly higher Ca content compared with the Si content and a clearly higher content of Ca compared with the peat A mixtures. There were still Ca-Mg oxides left in the bottom ash i.e. a less amount of sticky low temperature melting K-silicate rich melt was formed when peat B was added to the woody biomasses.

Place, publisher, year, edition, pages
2013. Vol. 27, no 7, p. 3997-4006
Keywords [en]
Chemical equilibriums, Combustion experiments, Elemental distribution, Energy dispersive x-ray, High-temperature melting, Inductively coupled plasma atomic emission spectroscopy, Low-temperature melting, Slagging characteristics, Aluminum, Ash handling, Ashes, Atomic emission spectroscopy, Biomass, Calcium, Combustion, Forestry, Fuels, Inductively coupled plasma, Mixtures, Pelletizing, Scanning electron microscopy, Silicates, Silicon, Slags, X ray diffraction, Peat, Ash, Pelleting, Slag
National Category
Engineering and Technology
Identifiers
URN: urn:nbn:se:ri:diva-48575DOI: 10.1021/ef400366dScopus ID: 2-s2.0-84880523196OAI: oai:DiVA.org:ri-48575DiVA, id: diva2:1474406
Available from: 2020-10-08 Created: 2020-10-08 Last updated: 2020-12-01Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus
By organisation
SP Energy Technology Center
In the same journal
Energy & Fuels
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 16 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf