Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Comparison and analysis of in-plane compression and bending failure in paperboard
RISE., Innventia.ORCID-id: 0000-0002-9689-5966
RISE., Innventia.
2016 (engelsk)Inngår i: Nordic Pulp & Paper Research Journal, ISSN 0283-2631, E-ISSN 2000-0669, Vol. 31, nr 3, s. 432-440Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

In-plane compression of paperboard, using long (LCT) and short compression test (SCT), and bend-ing, using the L&W creasability tester, have been ana-lyzed using three paperboards with similar strength prop-erties but different ZD profiles. The failure loads from the methods have been compared and the failure mechanisms analyzed. It was shown that at maximum bending moment from bending of samples using L=10 mm and L=50 mm, the SCT value and the maximum bending force from LCT all varied linearly with each other, indicating that same dam-age mechanism is activated. It was suggested that delamination cracks were initiated during SCT and LCT as well as during bending when plastic deformation had been initiated in an outer ply subjected to compressive stress. The plastic deformation would be initiated when the yield stress in the ply was reached, determined by an in-plane tensile test. When plastic deformation takes place, it will generate shear induced delamination cracks in locations with low shear strengths, e.g. in the interfaces or within the middle ply. The location depends on the material design strategy used in manufacturing the paper quality. To control the in-plane compression properties in pa-perboard one should control the yield stress (or possibly the failure stress) of the outer plies. Increased stress gives higher in-plane compression strength. Moreover, the interfaces strength is important, since increased interface strength (or lack of interfaces) prevents delamination.

sted, utgiver, år, opplag, sider
2016. Vol. 31, nr 3, s. 432-440
Emneord [en]
Compressive properties, Delamination, Folding, Mechanical properties, Paperboard, Shear properties
HSV kategori
Identifikatorer
URN: urn:nbn:se:ri:diva-12614DOI: 10.3183/npprj-2016-31-03-p432-440Scopus ID: 2-s2.0-84982190136OAI: oai:DiVA.org:ri-12614DiVA, id: diva2:971052
Tilgjengelig fra: 2016-09-15 Laget: 2016-09-15 Sist oppdatert: 2020-12-01bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Person

Nygårds, Mikael

Søk i DiVA

Av forfatter/redaktør
Nygårds, Mikael
Av organisasjonen
I samme tidsskrift
Nordic Pulp & Paper Research Journal

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 90 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
v. 2.43.0