Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Study of the Eutectoid Transformation in Grey Cast Irons and Its Effect on Mechanical Properties
RISE., SP – Sveriges Tekniska Forskningsinstitut, SP Sveriges tekniska forskningsinstitut, SP – Sveriges Tekniska Forskningsinstitut / Hållfasthet (BMh).ORCID-id: 0000-0002-6657-1792
RISE., Swerea, SWECAST.
2010 (engelsk)Inngår i: Key Engineering Materials, Vol. 457, s. 157-162Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

In this experimental study, six pearlitic grey cast irons with different Cu and Cr content, different section thicknesses and different eutectoid cooling rates have been examined. The eutectoid cooling rate was approximated by casting simulation analysis. The purpose of the experiments was to study the effect of the matrix structure on the overall mechanical properties. An emphasis is put on the pearlite interlamellar spacing because this controls the resulting mechanical properties to a large extent. By keeping the graphite structure constant, the effect of the matrix structure was able to be studied. This was achieved by shake-out at temperatures above the eutectoid transformation range followed by subsequent cooling in air, mould or in a furnace. The pearlite interlamellar spacing ranged from 90 to 330 nm for the matrices studied. Comparing the strength of the fine structured and coarse structured materials, the tensile and yield strength was reduced by almost 50%. Regarding the elastic deformation, a weak increase in the tangent modulus with increasing alloying content was observed. It was also observed that lower cooling rate decreased the tangent modulus. The tangent modulus ranged between 70 and 110 GPa. Analysing the plastic deformation of the materials, in terms of strain hardening exponent, n, and strength coefficient, K, a strong dependence on the pearlite coarseness was observed. It was concluded that the effect of graphite particle length on tensile strength was negligible and the major improvement on the strength was due to refinement of the pearlite.

sted, utgiver, år, opplag, sider
2010. Vol. 457, s. 157-162
HSV kategori
Identifikatorer
URN: urn:nbn:se:ri:diva-6169DOI: 10.4028/www.scientific.net/KEM.457.157Scopus ID: 2-s2.0-78651446626Lokal ID: 11528OAI: oai:DiVA.org:ri-6169DiVA, id: diva2:964004
Tilgjengelig fra: 2016-09-08 Laget: 2016-09-08 Sist oppdatert: 2023-06-08bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Person

Sjögren, Torsten

Søk i DiVA

Av forfatter/redaktør
Sjögren, Torsten
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 35 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
v. 2.43.0