Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Delreparation av tätskiktssystem: del 1    Pilotundersökningar i labb
RISE Research Institutes of Sweden, Samhällsbyggnad, Bygg och fastighet.ORCID-id: 0000-0002-8705-2828
2020 (Svenska)Rapport (Övrigt vetenskapligt)
Abstract [en]

 Pilot surveys in labs This project is the first part of an intended major project to verify methods for partial repairs and methods for quality assurance of these repairs. This part of the project is implemented in order to make the next part of the project (Part 2. Field study) credible and valid. The purpose is to investigate whether selected measurement systems are capable of warning of excess moisture where leakage occurs so that there is no consequential damage to the building. The aim of this part is to evaluate and build knowledge about how sensors should be used and the possibility to interpret results from these. The study of the function of the warning systems for moisture and water damage that will be used in the future field study has been carried out in a mock-up that has been developed within the project. The project has been carried out with five different moisture sensor systems. During the entire test period, RISE have carried out measurements of temperature and moisture level in the test set’s timber framework compartments. Measured values from the five moisture sensor systems have been compared to values from RISE's calibrated temperature and humidity sensors. The surveys carried out can be grouped as follows: • Function control of the moisture system's ability to detect elevated moisture levels in each mock-up’s framework. • Loading of undamaged floor and wall penetrations with water  • Loading of pre-damaged floor and wall penetrations with water  • Loading of partially repaired floor and wall penetrations with water  Function control Moisture sensor systems 2, 3, 4 and 5 show a relatively good compliance with RISE's calibrated moisture and temperature sensors, usually only a few percentage points deviation is noted. Note that the test procedure selected is not relevant for Invisense’s moisture sensor system (system 1) as these are located in different positions than the other moisture sensor systems. Loading of undamaged floor and wall penetrations with water  Floor When loading the floors with water, leakage was noted in test space 1 already after two hours of loading. This was recorded by the moisture sensors located in test compartment 1. Wall Already a few minutes after commencement of water spraying, a rising moisture level was observed and also recorded by the moisture sensors in test compartment 3. It is worth noting that this leakage was so small that no free water was detected. An increase in moisture level was recorded at the wall penetrations in test compartment 4 after about 10 hours. At the end of the spraying cycle the moisture sensor sample in compartment 1 also showed a raised value. Loading of pre-damaged floor and wall penetrations with water  Floor All of the floor drains were subjected to pre-test damage, which consisted in removal of the clamping ring, cutting of the collar in one place and splitting it open a few centimetres. All moisture sensor systems used in the floor wells in test compartments 1-4 indicated elevated values. Wall Pre-test damage to all wall penetrations was carried out using an awl that was pressed into the space between the tile and wall box and thus puncturing the sealing collar. All moisture sensor systems used in the wall penetrations in test compartments 1-4 indicated elevated values. Loading of partially repaired floor and wall penetrations with water  Floor After partial repair where all floor drains were replaced, water loading of the floor was again carried out with 100 mm water.  No leakage was detected during the 5-day water load. None of the moisture sensor systems indicated any leakage. Wall After the partial repair where all pipe collars were replaced, water spraying took place again with alternating cold and warm water (1500 times).  No leakage was detected. None of the moisture sensor systems indicated any leakage.

Conclusion • All moisture sensor systems in the study have the capability to show that leakage has occurred • It is not the absolute measured value of the moisture level that determines whether the waterproofing system is leaking or not  

It is the change in the moisture level in the construction itself that is crucial to the question as to whether it is to be opened up or not.

Ort, förlag, år, upplaga, sidor
2020. , s. 53
Serie
RISE Rapport ; 2020:41
Serie
SBUF rapport ; 13740
Nyckelord [sv]
Delreparation, reparation, tätskiktssystem, tätskikt, fuktsensorer, fuktgivar
Nationell ämneskategori
Naturvetenskap
Identifikatorer
URN: urn:nbn:se:ri:diva-46661ISBN: 978-91-89167-23-0 (digital)OAI: oai:DiVA.org:ri-46661DiVA, id: diva2:1460044
Anmärkning

RISE Research Institutes of Sweden har fått förtroendet från SBUF (Svenska Byggbranschens Utvecklingsfond) att utföra detta utvecklingsprojekt nr. 13 740.

Tillgänglig från: 2020-08-21 Skapad: 2020-08-21 Senast uppdaterad: 2023-06-08Bibliografiskt granskad

Open Access i DiVA

fulltext(5466 kB)347 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 5466 kBChecksumma SHA-512
2807e138badc54672a2bc5e00e76a920c74e244e6d5d3b1bb149a08aa8c5906a5afbc380b0225cb6a74735fa07f46548349da572993664bb241aae4582e67e78
Typ fulltextMimetyp application/pdf

Övriga länkar

Fulltext

Person

Antonsson, Ulf

Sök vidare i DiVA

Av författaren/redaktören
Antonsson, Ulf
Av organisationen
Bygg och fastighet
Naturvetenskap

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 347 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 161 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf