Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Experimental determination of the permeability of engineering textiles: Benchmark II
Ecole Polytechnique de Montreal, Canada.
Ecole Polytechnique de Montreal, Canada.
University of Delaware, USA.
University of Delaware, USA.
Show others and affiliations
2014 (English)In: Composites. Part A, Applied science and manufacturing, ISSN 1359-835X, E-ISSN 1878-5840, Vol. 61, p. 172-184Article in journal (Refereed) Published
Abstract [en]

In this second international permeability benchmark, the in-plane permeability values of a carbon fabric were studied by twelve research groups worldwide. One participant also investigated the deformation of the tested carbon fabric. The aim of this work was to obtain comparable results in order to make a step toward standardization of permeability measurements. Unidirectional injections were thus conducted to determine the unsaturated in-plane permeability tensor of the fabric. Procedures used by participants were specified in the guidelines defined for this benchmark. Participants were asked to use the same values for parameters such as fiber volume fraction, injection pressure and fluid viscosity to minimize sources of scatter. The comparison of the results from each participant was encouraging. The scatter between data obtained while respecting the guidelines was below 25%. However, a higher dispersion was observed when some parameters differed from the recommendations of this exercise.

Place, publisher, year, edition, pages
Elsevier Ltd , 2014. Vol. 61, p. 172-184
Keywords [en]
A. Fabrics/textiles, D. Process monitoring, E. Resin flow, Permeability, Mechanical permeability, Process monitoring, Experimental determination, Fabrics/textiles, Fiber volume fractions, Fluid viscosity, In-plane permeability, Injection pressures, Permeability measurements, Resin flows, Carbon
National Category
Engineering and Technology
Identifiers
URN: urn:nbn:se:ri:diva-45436DOI: 10.1016/j.compositesa.2014.02.010Scopus ID: 2-s2.0-84896474751OAI: oai:DiVA.org:ri-45436DiVA, id: diva2:1457706
Note

CODEN: CASMF; Correspondence Address: Ruiz, E.; Département de Génie Mécanique, École Polytechnique de Montréal, Succursale Centre-Ville, C.P. 6079, Montréal, QC H3C 3A7, Canada; email: edu.ruiz@polymtl.ca

Available from: 2020-08-12 Created: 2020-08-12 Last updated: 2020-12-01Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus
By organisation
SICOMP
In the same journal
Composites. Part A, Applied science and manufacturing
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 26 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf