Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Photonic materials for high-temperature applications: Synthesis and characterization by X-ray ptychographic tomography
Hamburg University, Germany. (Institute of Advanced Ceramics)
Helmholtz-Zentrum Geesthacht, Germany.ORCID-id: 0000-0002-3586-5763
Paul Scherrer Institut, Switzerland.
Paul Scherrer Institut, Switzerland.
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Applied Materials Today, ISSN 2352-9407, Vol. 13, s. 359-369Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Photonic materials for high-temperature applications need to withstand temperatures usually higher than 1000 °C, whilst keeping their function. When exposed to high temperatures, such nanostructured materials are prone to detrimental morphological changes, however the structure evolution pathway of photonic materials and its correlation with the loss of material's function is not yet fully understood. Here we use high-resolution ptychographic X-ray computed tomography (PXCT) and scanning electron microscopy (SEM) to investigate the structural changes in mullite inverse opal photonic crystals produced by a very-low-temperature (95 °C) atomic layer deposition (ALD) super-cycle process. The 3D structural changes caused by the high-temperature exposure were quantified and associated with the distinct structural features of the ceramic photonic crystals. Other than observed in photonic crystals produced via powder colloidal suspensions or sol-gel infiltration, at high temperatures of 1400 °C we detected a mass transport direction from the nano pores to the shells. We relate these different structure evolution pathways to the presence of hollow vertexes in our ALD-based inverse opal photonic crystals. Although the periodically ordered structure is distorted after sintering, the mullite inverse opal photonic crystal presents a photonic stopgap even after heat treatment at 1400 °C for 100 h.

Ort, förlag, år, upplaga, sidor
2018. Vol. 13, s. 359-369
Nyckelord [en]
Ptychography X-ray computed tomography, 3D image analysis, Low-temperature atomic layer deposition, Photonic materials, High-temperature applications
Nationell ämneskategori
Signalbehandling Kompositmaterial och -teknik Nanoteknik Annan data- och informationsvetenskap Acceleratorfysik och instrumentering
Identifikatorer
URN: urn:nbn:se:ri:diva-36638DOI: 10.1016/j.apmt.2018.10.002Scopus ID: 2-s2.0-85055731716OAI: oai:DiVA.org:ri-36638DiVA, id: diva2:1271641
Tillgänglig från: 2018-12-17 Skapad: 2018-12-17 Senast uppdaterad: 2020-07-29Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopushttps://doi.org/10.1016/j.apmt.2018.10.002

Person

Larsson, Emanuel

Sök vidare i DiVA

Av författaren/redaktören
Larsson, Emanuel
SignalbehandlingKompositmaterial och -teknikNanoteknikAnnan data- och informationsvetenskapAcceleratorfysik och instrumentering

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 68 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf