Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Acceptanskriterier för repor och intryck i plaströr Accpetance criteria for scratches and indentations in plastic pipes
RISE., SP – Sveriges Tekniska Forskningsinstitut, SP Sveriges tekniska forskningsinstitut, SP – Sveriges Tekniska Forskningsinstitut / Göteborg (BMg).
RISE., SP – Sveriges Tekniska Forskningsinstitut, SP Sveriges tekniska forskningsinstitut, SP – Sveriges Tekniska Forskningsinstitut / Hållfasthet (BMh).ORCID-id: 0000-0002-3481-1368
RISE., SP – Sveriges Tekniska Forskningsinstitut, SP Sveriges tekniska forskningsinstitut, SP – Sveriges Tekniska Forskningsinstitut / Hållfasthet (BMh).
RISE., SP – Sveriges Tekniska Forskningsinstitut, SP Sveriges tekniska forskningsinstitut, SP – Sveriges Tekniska Forskningsinstitut / Göteborg (BMg).
Visa övriga samt affilieringar
2009 (Svenska)Rapport (Refereegranskat)
Abstract [sv]

Development of materials and laying techniques have arisen the question how scratches and indentations in plastics pipes affect the strength and technical lifetime of pipelines. Scratches may occur both in the manufacturing of the pipes, in connection with the installation and subsequent maintenance. The problems in assessing the failure risk from scratches and indentations are similar for pipes used in gas and water distribution and in district heating applications. Therefore, a broad effort to identify the risks in relation to current pipe materials is technically and economically justified. The project has aimed to evaluate the effect of scratches and indentations on the technical lifetime of plastics pipes and to present criteria for maximum allowable depth of scratches and indentations. The study on pressure pipes focused on the conditions for scratched polyethylene pipes to achieve a lifetime of 50 years. It is noted that a scratch damage can not be judged solely on the basis of its depth and sharpness. To assess the impact of the scratch on the serviceability of the pipe, consideration must also be taken to the material from which the pipe was made and the safety factor used in the design. Extensive pressure tests show that pipes made of modern materials can withstand surface scratches to a higher degree than pipes of older materials. For pipes made of modern bimodal PE80 and PE100 materials, scratches up to 10% depth may be accepted without reduction of rated pressure. However, for pipes of older material, a reduction in pressure may be required already at smaller scratches. The study also indicates that for the same relative scratch depth, a greater reduction in pressure is required with increasing pipe dimension. The study on the non pressure pipes shows that the studied polypropylene pipes resist both deep scratches combined with ovalization and large indentations without any cracks penetrating the pipe wall. However, the extent and development of crazing and surface cracking vary with scratch depth, deformation level and material. The test pipes were subjected to extreme conditions very rarely or never occurring in practice. This suggests that small scratches at moderate ovalization and realistic indentations in temperatures around room temperature do not affect the lifetime of the pipes. One objective of the project was to develop a method for the evaluation of the scratch resistance of a pipe. In the proposed test method the force needed to produce a specified scratch is measured. This force is used as a relative measure of the scratch resistance of a pipe material when compared to other materials. In order to assess to what extent a scratch affects the lifetime of the pipe, the depth of the scratch must be estimated with reasonable accuracy. Since the scratch in many cases is found on existing pipelines the method must be suited for field use. To achieve that a simple instrument for scratch depth measurements was made and evaluated.

Ort, förlag, år, upplaga, sidor
2009.
Serie
SP Rapport, ISSN 0284-5172 ; 2009:21
Nationell ämneskategori
Naturvetenskap
Identifikatorer
URN: urn:nbn:se:ri:diva-4864Lokalt ID: 10165ISBN: 978-91-86319-08-3 (tryckt)OAI: oai:DiVA.org:ri-4864DiVA, id: diva2:962503
Anmärkning

The publication is also translated into English

Tillgänglig från: 2016-09-07 Skapad: 2016-09-07 Senast uppdaterad: 2023-05-25Bibliografiskt granskad

Open Access i DiVA

fulltext(4568 kB)536 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 4568 kBChecksumma SHA-512
92e2e4ea9577d4e11cb83cf7758e6320f5f67f6cf97978e4981f9df04049b6f95a8a1bf498a90484b0a61b485148186260fc182561625ad9780340e97e5e8646
Typ fulltextMimetyp application/pdf

Person

Flansbjer, Mathias

Sök vidare i DiVA

Av författaren/redaktören
Flansbjer, Mathias
Av organisationen
SP – Sveriges Tekniska Forskningsinstitut / Göteborg (BMg)SP – Sveriges Tekniska Forskningsinstitut / Hållfasthet (BMh)
Naturvetenskap

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 536 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 431 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf