Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Surface integrity after post processing of EDM processed Inconel 718 shaft
RISE - Research Institutes of Sweden, Swerea, Swerea IVF AB. University West, Sweden.ORCID-id: 0000-0003-2991-2911
GKN Aerospace Sweden AB, Sweden.
RISE - Research Institutes of Sweden, Swerea, Swerea IVF AB.ORCID-id: 0000-0003-3656-1806
University West, Sweden.
2018 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 95, nr 5-8, s. 2325-2337Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Electrical discharge machining (EDM) is considered as an efficient alternative to conventional material removal concepts that allows for much higher material removal rates. However, EDM generates unwanted features such as re-cast layer (RCL), tensile residual stresses and a rough surface. In order to recover the surface integrity, different post processes has been compared: high-pressure water jet (HPWJ), grit blasting (GB) and shot peening (SP). Surface integrity has been evaluated regarding microstructure, residual stresses, chemical content and surface roughness. The results showed that a combination of two post processes is required in order to restore an EDM processed surface of discontinuous islands of RCL. HPWJ was superior for removing RCL closely followed by grit blasting. However, grit blasting showed embedded grit blasting abrasive into the surface. Regarding surface roughness, it was shown that both grit blasting and HPWJ caused a roughening of the surface topography while shot peening generates a comparably smoother surface. All three post processes showed compressive residual stresses in the surface where shot peening generated the highest amplitude and penetration depths. However, the microstructure close to the surface revealed that shot peening had generated cracks parallel to the surface. The results strongly state how important it is to evaluate the surface at each of the different subsequent process steps in order to avoid initiation of cracks. © 2017 The Author(s)

Ort, förlag, år, upplaga, sidor
2018. Vol. 95, nr 5-8, s. 2325-2337
Nyckelord [en]
Abrasive water jet, EDM, Grit blasting, Inconel 718, Shot peening, Surface integrity, Abrasives, Blasting, Cracks, Electric discharge machining, Electric discharges, Jets, Microstructure, Residual stresses, Surface roughness, Surface topography, Compressive residual stress, Electrical discharge machining, High-pressure water jets, Inconel-718, Tensile residual stress, Fighter aircraft
Nationell ämneskategori
Naturvetenskap
Identifikatorer
URN: urn:nbn:se:ri:diva-33155DOI: 10.1007/s00170-017-1342-6Scopus ID: 2-s2.0-85034646822OAI: oai:DiVA.org:ri-33155DiVA, id: diva2:1178028
Tillgänglig från: 2018-01-26 Skapad: 2018-01-26 Senast uppdaterad: 2020-01-30Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Holmberg, JonasBerglund, Johan

Sök vidare i DiVA

Av författaren/redaktören
Holmberg, JonasBerglund, Johan
Av organisationen
Swerea IVF AB
I samma tidskrift
The International Journal of Advanced Manufacturing Technology
Naturvetenskap

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 25 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
v. 2.35.9