From an economic and environmental perspective, the use of less chemicals in the production of cellulose nanofibrils (CNFs) is advantageous. In this study, we investigated the oxidation (TEMPO/NaClO2/NaClO, pH 6.8) of softwood (SW) particles with varying amounts of TEMPO (16, 8 or 0 mg g−1 of wood). Following, TEMPO-oxidized SW nanofibrils (TO-SWNFs) were obtained by nanofibrillation and their size, morphology, and crystallite size were assessed. Hydrogel networks of TO-SWNFs were prepared and mechanical properties were measured in dH2O and phosphate buffered saline (PBS) to compare their performance for possible biomedical applications such as wound dressings. The results reveal that the presence of TEMPO is of importance for TO-SWNF network properties, presenting higher eq. H2O absorption (≈2500 %) and elongation at break (≈10 %) with good wet strength (≈180 kPa). In addition, a decrease in use of TEMPO catalyst from 16 to 8 mg g−1 of wood is possible, without detrimental effects on hydrogel network properties (dH2O absorption ≈ 2000 %, elongation at break ≈ 13 %, wet strength ≈ 190 kPa) related to applications as wound dressings. 

To commercialize a biomedical product as a medical device, reproducibility of production and time-stability are important parameters. Studies of reproducibility are lacking in the literature. Additionally, chemical pre-treatments of wood fibres to produce highly fibrillated cellulose nanofibrils (CNF) seem to be demanding in terms of production efficiency, being a bottleneck for industrial upscaling. In this study, we evaluated the effect of pH on the dewatering time and washing steps of 2,2,6,6-Tetramethylpiperidinyloxy (TEMPO)-mediated oxidized wood fibres when applying 3.8 mmol NaClO/g cellulose. The results indicate that the method does not affect the carboxylation of the nanocelluloses, and levels of approximately 1390 μmol/g were obtained with good reproducibility. The washing time of a Low-pH sample was reduced to 1/5 of the time required for washing a Control sample. Additionally, the stability of the CNF samples was assessed over 10 months and changes were quantified, the most pronounced were the increase of potential residual fibre aggregates, reduction of viscosity and increase of carboxylic acid content. The cytotoxicity and skin irritation potential were not affected by the detected differences between the Control and Low-pH samples. Importantly, the antibacterial effect of the carboxylated CNFs against S. aureus and P. aeruginosa was confirmed. © 2023 The Authors

From a circular economy perspective, one-pot strategies for the isolation of cellulose nanomaterials at a high yield and with multifunctional properties are attractive. Here, the effects of lignin content (bleached vs unbleached softwood kraft pulp) and sulfuric acid concentration on the properties of crystalline lignocellulose isolates and their films are explored. Hydrolysis at 58 wt % sulfuric acid resulted in both cellulose nanocrystals (CNCs) and microcrystalline cellulose at a relatively high yield (>55%), whereas hydrolysis at 64 wt % gave CNCs at a lower yield (<20%). CNCs from 58 wt % hydrolysis were more polydisperse and had a higher average aspect ratio (1.5-2×), a lower surface charge (2×), and a higher shear viscosity (100-1000×). Hydrolysis of unbleached pulp additionally yielded spherical nanoparticles (NPs) that were <50 nm in diameter and identified as lignin by nanoscale Fourier transform infrared spectroscopy and IR imaging. Chiral nematic self-organization was observed in films from CNCs isolated at 64 wt % but not from the more heterogeneous CNC qualities produced at 58 wt %. All films degraded to some extent under simulated sunlight trials, but these effects were less pronounced in lignin-NP-containing films, suggesting a protective feature, but the hemicellulose content and CNC crystallinity may be implicated as well. Finally, heterogeneous CNC compositions obtained at a high yield and with improved resource efficiency are suggested for specific nanocellulose uses, for instance, as thickeners or reinforcing fillers, representing a step toward the development of application-tailored CNC grades. © 2023 The Authors. 

The effect on softwood fiber wall nanostructure of kraft cooking, oxygen delignification and refining was evaluated by X-ray scattering. A recently developed simulation method for modelling small angle X-ray scattering (SAXS) data was used to estimate the apparent average sizes of solids (AAPS) and interstitial spaces in the fiber wall (AACS). Fiber saturation point and wide angle X-ray scattering were also used to calculate the pore volume in the fiber wall and the crystallite size of the fibril, respectively. The experimental modelled SAXS data was able to give consistent values for each kraft-cooked and oxygen-delignified pulp. Kraft delignification seems to have the major influence on the fiber nanostructure modification, while oxygen delignification has little or no significant impact even for different kappa numbers. The particle sizes values were more stable than the cavities sizes and no significant differences were seen between different delignification processes, refining or delignification degree. Pulps evaluated after PFI-refining, showed an increase in the fiber wall porosity evaluated by FSP and an increase in the interstitial spaces in the fiber wall, while the crystallite size and the particle sizes were very little or not affected at all. 

A simulation method was developed for modelling SAXS data recorded on cellulose rich pulps. The modelling method is independent of the establishment of separate form factors and structure factors and was used to model SAXS data recorded on dense samples. An advantage of the modelling method is that it made it possible to connect experimental SAXS data to apparent average sizes of particles and cavities at different sample solid contents. Experimental SAXS data could be modelled as a superposition of a limited number of simulated intensity components and gave results in qualitative agreement with CP/MAS 13C-NMR data recorded on the same samples. For the water swollen samples, results obtained by the SAXS modelling method and results obtained from CP/MAS 13C-NMR measurements, agreed on the ranking of particle sizes in the different samples. The SAXS modelling method is dependent on simulations of autocorrelation functions and the time needed for simulations could be reduced by rescaling of simulated correlation functions due to their independence of the choice of step size in real space. In this way an autocorrelation function simulated for a specific sample could be used to generate SAXS intensity profiles corresponding to all length scales for that sample and used for efficient modelling of the experimental data recorded on that sample. Graphical abstract: [Figure not available: see fulltext.] © 2021, The Author(s).

Cellulose rich and cellulose enriched pulps are com. important and scientifically interesting materials with a complex hierarchical fiber wall nanostructure which change with moisture sorption and swelling in water. The fiber wall building blocks and cavities are in size ranges addressable by small angle x-ray scattering (SAXS) but due to large variability in sizes and shapes, extracting quant. data about the fiber wall nanostructure from SAXS data can be challenging. For this purpose, a simulation method was developed for modeling SAXS data recorded on cellulose rich pulps. The modeling method is independent of the establishments of sep. form factors and structure factors and was used to model SAXS data recorded on dense samples. An advantage of the modeling method was that it made it possible to connect exptl. SAXS data to apparent average sizes of particles and cavities at different sample solid contents. Exptl. SAXS data could be modelled as a superposition of a limited number of simulated intensity components and gave results in qual. agreement with CP/MAS 13C-NMR data recorded on the same samples. For the water swollen samples, results obtained by the SAXS modeling method and results obtained from CP/MAS 13C-NMR measurements, agreed on the ranking of particle sizes in the different samples. The SAXS modeling method is dependent on simulations of autocorrelation functions. The time needed for simulations could be reduced by rescaling of simulated correlation functions, due to their independence of the choice of step size in real space. This way an autocorrelation function simulated for a specific sample could be used to generate SAXS intensity profiles corresponding to all length scales for that sample and used for efficient modeling of the exptl. data recorded on that sample.

The biotechnological applications of cellulose nanocrystals (CNCs) continue to grow due to their sustainable nature, impressive mechanical, rheological, and emulsifying properties, upscaled production capacity, and compatibility with other materials, such as protein and polysaccharides. In this study, hydrogels from CNCs and pectin, a plant cell wall polysaccharide broadly used in food and pharma, were produced by calcium ion-mediated internal ionotropic gelation (IG). In the absence of pectin, a minimum of 4 wt% CNC was needed to produce self-supporting gels by internal IG, whereas the addition of pectin at 0.5 wt% enabled hydrogel formation at CNC contents as low as 0.5 wt%. Experimental data indicate that CNCs and pectin interact to give robust and self-supporting hydrogels at solid contents below 2.5 %. Potential applications of these gels could be as carriers for controlled release, scaffolds for cell growth, or wherever else distinct and porous network morphologies are required.

The effect of initial stages of pulping of spruce, resembling prehydrolysis and alkaline cooking was studied using CP/MAS 13C-NMR, X-ray scattering, FSP and carbohydrate composition in order to study the impact of the pre-treatments on the fiber wall nanostructure. Removal of fiber wall components, hemicellulose and lignin, increased the fiber wall porosity and induced cellulose fibril aggregation. The effect of temperature and pH in the treatment on cellulose fibril aggregate size appears to be secondary. It is the removal of hemicellulose that has a profound effect on the supramolecular structure of the cellulose fiber wall. As the amount of hemicellulose dissolved from wood increases, the fibril aggregate size determined by NMR increases as well, ranging from 16 to 28 nm. Specifically, a good correlation between the amount of glucomannan in the fiber wall and the fibril aggregate size is seen. The lower the amount of glucomannan, the larger the aggregate size. Glucomannan thus seems to prevent aggregation as it acts as a very efficient spacer between fibrils. Elemental fibril size determined by NMR, was quite similar for all samples, ranging from 3.6 to 4.1 nm. By combining measurement methods, a more well-resolved picture of the structural changes occurring during was obtained. © 2021, The Author(s).

Cellulose nanofibrils (CNFs) were obtained by applying a chemical pretreatment consisting of autoclaving the pulp fibers in sodium hydroxide, combined with 2,2,6,6-tetramethylpiperidinyl-1-oxyl-mediated oxidation. Three levels of sodium hypochlorite were applied (2.5, 3.8, and 6.0 mmol/g) to obtain CNF qualities (CNF_2.5, CNF_3.8, and CNF_6.0) with varying content of carboxyl groups, that is, 1036, 1285, and 1593 μmol/g cellulose. The cytotoxicity and skin irritation potential (indirect tests) of the CNFs were determined according to standardized in vitro testing for medical devices. We here demonstrate that autoclaving (121 °C, 20 min), which was used to sterilize the gels, caused a modification of the CNF characteristics. This was confirmed by a reduction in the viscosity of the gels, a morphological change of the nanofibrils, by an increase of the ultraviolet-visible absorbance maxima at 250 nm, reduction of the absolute zeta potential, and by an increase in aldehyde content and reducing sugars after autoclaving. Fourier-transform infrared spectroscopy and wide-angle X-ray scattering complemented an extensive characterization of the CNF gels, before and after autoclaving. The antibacterial properties of autoclaved carboxylated CNFs were demonstrated in vitro (bacterial survival and swimming assays) on Pseudomonas aeruginosa and Staphylococcus aureus. Importantly, a mouse in vivo surgical-site infection model on S. aureus revealed that CNF_3.8 showed pronounced antibacterial effect and performed as good as the antiseptic Prontosan wound gel.

Abstract: Moisture absorption in the cell wall structure of wood is well known to induce considerable swelling of the wood exerting high expansion forces. This swelling is mainly induced by the sorptive action of the hydroxyl groups of the carbohydrate wood polymers; cellulose and hemicelluloses. On the ultrastructural level, there are, however, still questions with regard to the detailed deformations induced by this moisture absorption. Here, FTIR spectroscopy and synchrotron-radiation-based X-ray diffraction were used on paper samples to study the deformation of the cellulose crystals as a consequence of moisture absorption and desorption. Both techniques revealed that the moisture absorption resulted in a transverse contraction of the cellulose crystals accompanied by a somewhat smaller elongation in the cellulose chain direction. The deformations were found to be a direct response to the increased moisture content and were also found to be reversible during moisture desorption. It is hypothesised that these deformations are a consequence of the swelling forces created by the combined longitudinal and lateral expansions of the non-crystalline cellulose molecules and the glucomannan hemicellulose aligned along the cellulose crystals. These forces will impose a lateral contraction of the cellulose crystals, as well as a longitudinal extension of it. Graphic abstract: [Figure not available: see fulltext.]. © 2021, The Author(s).