Endre søk
Link to record
Permanent link

Direct link
BETA
Sjöholm, Elisabeth, Associiate ProfessorORCID iD iconorcid.org/0000-0002-4858-7352
Publikasjoner (10 av 24) Visa alla publikasjoner
Bengtsson, A., Bengtsson, J., Sedin, M. & Sjöholm, E. (2019). Carbon Fibers from Lignin-Cellulose Precursors: Effect of Stabilization Conditions. ACS Sustainable Chemistry and Engineering, 7(9), 8440-8448
Åpne denne publikasjonen i ny fane eller vindu >>Carbon Fibers from Lignin-Cellulose Precursors: Effect of Stabilization Conditions
2019 (engelsk)Inngår i: ACS Sustainable Chemistry and Engineering, ISSN 2168-0485, Vol. 7, nr 9, s. 8440-8448Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

There is an increasing demand for lightweight composites reinforced with carbon fibers (CFs). Due to its high availability and carbon content, kraft lignin has gained attention as a potential low-cost CF precursor. CFs with promising properties can be made from flexible dry-jet wet spun precursor fibers (PFs) from blends (70:30) of softwood kraft lignin and fully bleached softwood kraft pulp. This study focused on reducing the stabilization time, which is critical in CF manufacturing. The impact of stabilization conditions on chemical structure, yield, and mechanical properties was investigated. It was possible to reduce the oxidative stabilization time of the PFs from about 16 h to less than 2 h, or even omitting the stabilization step, without fusion of fibers. The main reactions involved in the stabilization stage were dehydration and oxidation. The results suggest that the isothermal stabilization at 250 °C override the importance of having a slow heating rate. For CFs with a commercial diameter, stabilization of less than 2 h rendered in tensile modulus 76 GPa and tensile strength 1070 MPa. Impregnation with ammonium dihydrogen phosphate significantly increased the CF yield, from 31-38 to 46-50 wt %, but at the expense of the mechanical properties.

sted, utgiver, år, opplag, sider
American Chemical Society, 2019
Emneord
Ammonium dihydrogen phosphate, Lignin, Mechanical properties, Carbon fibers, Kraft pulp, Reinforced plastics, Softwood, Spinning, Tensile strength, Textile blends, Bleached softwood kraft pulp, Cellulose precursor, Dry jet-wet spinning, Lightweight composites, Oxidative stabilization, Softwood kraft lignin, Stabilization
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-38937 (URN)10.1021/acssuschemeng.9b00108 (DOI)2-s2.0-85065403539 (Scopus ID)
Forskningsfinansiär
Swedish Energy Agency
Tilgjengelig fra: 2019-06-03 Laget: 2019-06-03 Sist oppdatert: 2019-06-18bibliografisk kontrollert
Bengtsson, A. & Sjöholm, E. (2018). Conditions for the stabilisation of lignin-cellulose prefibres for carbon fibre production. In: 15th European workshop on lignocellulosics and pulp: Proceedings for poster presentations. Paper presented at 15th European workshop on lignocellulosics and pulp, June 26-29, 2018, Aveiro, Portugal (pp. 111-114).
Åpne denne publikasjonen i ny fane eller vindu >>Conditions for the stabilisation of lignin-cellulose prefibres for carbon fibre production
2018 (engelsk)Inngår i: 15th European workshop on lignocellulosics and pulp: Proceedings for poster presentations, 2018, s. 111-114Konferansepaper, Publicerat paper (Annet vitenskapelig)
Abstract [en]

Stabilisation of the prefibre is a time-consuming step in carbon fibre (CF) production. In this paper the stabilisation condition of dry-jet wet-spun lignin-cellulose (LC) prefibres (70:30  t%) are reported. The impact of prefibre-impregnation by ammonium dihydrogen phosphate (ADHP) and various thermal conditions were evaluated by measuring the yield and mechanical properties of the final CFs. The addition of ADHP improved the CF yields from 32-40 wt% to 45-47 wt% but had a slight negative impact on the tensile modulus (TM) whereas no significant difference in tensile strength (TS) was observed. The absence of fibre fusion and glass transition temperature (Tg) indicate successful stabilisation of all prefibres. This implies possibilities of using short stabilisation times of LC prefibres in CF production.

Emneord
ADHP, carbon fibre, cellulose, lignin, stabilisation, tensile properties
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-35319 (URN)
Konferanse
15th European workshop on lignocellulosics and pulp, June 26-29, 2018, Aveiro, Portugal
Forskningsfinansiär
Swedish Energy Agency
Tilgjengelig fra: 2018-10-15 Laget: 2018-10-15 Sist oppdatert: 2018-11-15bibliografisk kontrollert
Bengtsson, A., Bengtsson, J., Olsson, C., Sedin, M., Jedvert, K., Theliander, H. & Sjöholm, E. (2018). Improved yield of carbon fibres from cellulose and kraft lignin. Holzforschung, 72(12), 1007-1016
Åpne denne publikasjonen i ny fane eller vindu >>Improved yield of carbon fibres from cellulose and kraft lignin
Vise andre…
2018 (engelsk)Inngår i: Holzforschung, ISSN 0018-3830, E-ISSN 1437-434X, Vol. 72, nr 12, s. 1007-1016Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

To meet the demand for carbon-fibre-reinforced composites in lightweight applications, cost-efficient processing and new raw materials are sought for. Cellulose and kraft lignin are each interesting renewables for this purpose due to their high availability. The molecular order of cellulose is an excellent property, as is the high carbon content of lignin. By co-processing cellulose and lignin, the advantages of these macromolecules are synergistic for producing carbon fibre (CF) of commercial grade in high yields. CFs were prepared from precursor fibres (PFs) made from 70:30 blends of softwood kraft lignin (SW-KL) and cellulose by dry-jet wet spinning with the ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate ([EMIm][OAc]) as a solvent. In focus was the impact of the molecular mass of lignin and the type of cellulose source on the CF yield and properties, while membrane-filtrated kraft lignin and cellulose from dissolving kraft pulp and fully bleached paper-grade SW-KP (kraft pulp) served as sources. Under the investigated conditions, the yield increased from around 22% for CF from neat cellulose to about 40% in the presence of lignin, irrespective of the type of SW-KL. The yield increment was also higher relative to the theoretical one for CF made from blends (69%) compared to those made from neat celluloses (48-51%). No difference in the mechanical properties of the produced CF was observed.

Emneord
1-ethyl-3-methylimidazolium acetate (EMIMAc), carbon fibre (CF), cellulose, dissolving pulp, dry-jet wet-spun, fractionation, kraft pulp, LignoBoost lignin, molecular mass, softwood kraft lignin, Carbon fibers, Dissolution, Fiber reinforced materials, Fiber reinforced plastics, Ionic liquids, Softwoods, 1-ethyl-3-methylimidazolium acetates, Carbon fibre reinforced composites, Dry jet-wet spinning, High carbon content, Lightweight application, Molecular ordering, Softwood kraft lignins, Lignin
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-34571 (URN)10.1515/hf-2018-0028 (DOI)2-s2.0-85050958001 (Scopus ID)
Tilgjengelig fra: 2018-08-13 Laget: 2018-08-13 Sist oppdatert: 2019-06-18bibliografisk kontrollert
Andersson, S., Bengtsson, A., Åkerström, M., Sedin, M. & Sjöholm, E. (2018). The impact of inorganic elements on lignin‐based carbon fibre quality. In: 15th European workshop on lignocelllulosics and pulp: Proceedings for poster presentations. Paper presented at 15th European workshop on lignocelllulosics and pulp, June 26-29, 2018, Aveiro, Portugal (pp. 119-122).
Åpne denne publikasjonen i ny fane eller vindu >>The impact of inorganic elements on lignin‐based carbon fibre quality
Vise andre…
2018 (engelsk)Inngår i: 15th European workshop on lignocelllulosics and pulp: Proceedings for poster presentations, 2018, s. 119-122Konferansepaper, Poster (with or without abstract) (Annet vitenskapelig)
Abstract [en]

The influence of inorganic elements on lignin ‐based carbon fibre (CF) quality was studied using sulphates of Na +, K+, Mg2+, Fe2+, Al3+. The metal sulphates were added to wet spun prefibres made from softwood kraft lignin (SKL):cellulose (70:30) and melt spun prefibres made from low molecular mass SKL. An increase in concentration from 0.1 w% to about 0.4 w% did neither affect the mechanical properties nor the morphology as observed by SEM. In contrast, metal sulphates added to the initial 0.45 w% to a total range 1.5 to 5.0 w%, was found detrimental to the melt spinning and to the final CF quality. Thus, the recommendation of <0.1 w% ash in kraft lignin may be exceeded, but more research is needed to establish the upper concentration limit.

Emneord
ash, carbon fibre, cellulose, inorganic elements, lignin
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-35320 (URN)
Konferanse
15th European workshop on lignocelllulosics and pulp, June 26-29, 2018, Aveiro, Portugal
Forskningsfinansiär
Swedish Energy Agency
Tilgjengelig fra: 2018-10-15 Laget: 2018-10-15 Sist oppdatert: 2018-11-15bibliografisk kontrollert
Sjöholm, E. (2017). 18th International Symposium on Wood, Fibre and Pulp Chemistry (ISWFPC) September 8-11 2015, Vienna, Austria. Stockholm: RISE Innventia
Åpne denne publikasjonen i ny fane eller vindu >>18th International Symposium on Wood, Fibre and Pulp Chemistry (ISWFPC) September 8-11 2015, Vienna, Austria
2017 (engelsk)Annet (Annet vitenskapelig)
Abstract [en]

A brief overview of the oral presentations and plenary lectures.

sted, utgiver, år, sider
Stockholm: RISE Innventia, 2017. s. 25
Serie
Innventia report ; 915
Emneord
biorefining, lignin
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-32710 (URN)
Tilgjengelig fra: 2017-11-20 Laget: 2017-11-20 Sist oppdatert: 2018-08-21bibliografisk kontrollert
Gustafsson, Å., Hale, S., Cornelissen, G., Sjöholm, E. & Gunnarsson, J. S. (2017). Activated carbon from kraft lignin: A sorbent for in situ remediation of contaminated sediments. Environmental technology and innovation, 7, 160-168
Åpne denne publikasjonen i ny fane eller vindu >>Activated carbon from kraft lignin: A sorbent for in situ remediation of contaminated sediments
Vise andre…
2017 (engelsk)Inngår i: Environmental technology and innovation, ISSN 23521864, Vol. 7, s. 160-168Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A new type of activated carbon derived from Kraft lignin, separated from black liquor in the paper pulp process, was evaluated for its use as an alternative sorbent to commercial powdered activated carbons (AC) from anthracite (ACCOAL) or coconut (ACBIO) for remediation in situ of contaminated sediments. Two types of kraft lignins (KL): (1) softwood (SKL), (2) hardwood (HKL) were first evaluated for their sorption to PAHs using assays in water with passive samplers (POMs). Results showed that without further chemical modifications the two kraft lignins tested had lower sorption coefficients than commercial ACCOAL or ACBIO and are not good sorbents for remediation. Following these initial tests a new type of AC derived from softwood (ACSKL) was produced in the lab using activation with potassium hydroxide (KOH) (lignin:KOH, 1:3 by dry weight) and pyrolysis at 700 °C. Sorption properties of the new ACSKL was compared to the other ACs in water spiked with PAHs and in water with PAH-contaminated sediment. Sorption results were also compared to bioavailability measurements, using digestive fluid extraction (DFE) in vitro, a method that mimics the solubilization of contaminants that occurs in the gut of a sediment-ingesting invertebrate. ACSKL was found to have similar surface area, pore volume and sorption coefficients as ACCOAL and ACBIO and thus offers a new potential sorbent for remediation, based on a more renewable biomass-derived source than AC from coal. Sediment amendment with 1% AC-SKL reduced the bioavailability of larger PAHs on average by 54% (measured by DFE), and reduced pore water concentrations of ΣPAH by 80% (measured with passive samplers). Our results show that a new type of AC based on softwood kraft lignin, a renewable and locally produced biomass material, could be used as an alternative sorbent for sediment and water remediation provided it is produced in sufficient amount and at a competitive price compared to other traditional ACs.

Emneord
kraft lignin, activated carbon
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-29294 (URN)10.1016/j.eti.2016.11.001 (DOI)2-s2.0-85014516625 (Scopus ID)
Tilgjengelig fra: 2017-04-18 Laget: 2017-04-18 Sist oppdatert: 2019-01-22bibliografisk kontrollert
Olsson, C., Sjöholm, E. & Reimann, A. (2017). Carbon fibres from precursors produced by dry-jet wet-spinning of kraft lignin blended with kraft pulps. Holzforschung, 71(4), 275-283
Åpne denne publikasjonen i ny fane eller vindu >>Carbon fibres from precursors produced by dry-jet wet-spinning of kraft lignin blended with kraft pulps
2017 (engelsk)Inngår i: Holzforschung, ISSN 0018-3830, E-ISSN 1437-434X, Vol. 71, nr 4, s. 275-283Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A part of kraft lignin (KL) can be used as a value-added product without detracting the chemical recovery and the energy balance of the kraft mill. The focus of this study is the production of light-weight carbon fibres (CFS) from KL obtained by the LignoBoost process. For this purpose, crude KL and various cellulose products from kraft pulping of hardwood (HW) and softwood (SW) were dissolved in 1-ethyl-3-methylimidazolium acetate ([EMIm][OAc]) and submitted to dry-jet wet-spun to obtain precursor fibres containing 70% KL and 30% cellulose, which were thermally stabilised and further converted by thermal treatments into CF. The initial and final products were characterised with respect to, e.g. mole mass distribution, thermal properties, tensile strength and tensile modulus determination. The optimised precursor fibres are smooth and flexible with similar mechanical properties as commercial textile fibres. The best CFS made had a tensile strength of 780 MPa and a tensile modulus of 68 GPa and are thus stronger and stiffer than those produced by melt-spinning of SW-based lignins alone. The new CFS based on dry-jet wet-spun precursors still have a high potential for further improvements.

Emneord
carbon fibre (CF), dry-jet wet-spun, ionic liquid (IL); kraft pulp, precursor fibre, softwood kraft lignin (KL), tensile modulus, tensile strength
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-29403 (URN)10.1515/hf-2016-0189 (DOI)2-s2.0-85016745985 (Scopus ID)
Tilgjengelig fra: 2017-04-26 Laget: 2017-04-26 Sist oppdatert: 2019-07-05bibliografisk kontrollert
Wang, M., Sjöholm, E. & Li, J. (2017). Fast and reliable quantification of lignin reactivity via reaction with dimethylamine and formaldehyde (Mannich reaction). Holzforschung, 71(1), 27-34
Åpne denne publikasjonen i ny fane eller vindu >>Fast and reliable quantification of lignin reactivity via reaction with dimethylamine and formaldehyde (Mannich reaction)
2017 (engelsk)Inngår i: Holzforschung, ISSN 0018-3830, E-ISSN 1437-434X, Vol. 71, nr 1, s. 27-34Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The influence of pH on the Mannich reaction (amino alkylation in the presence of formaldehyde) has been analyzed by liquid chromatography-mass spectrometry (LC-MS) with vanillin (VA) as a model compound and a purified softwood kraft lignin (SKL) as a substrate. The reaction products of VA were studied at pH 5, 7, and 9 at 60°C for 4 h. The Mannich adduct and side reaction products with methylene bridge were found at both pH 7 and 9, while only di-substituted by-products were observed at pH 5. Nitrogen contents determined from blank runs were substantial at pH 5 and negligible at pH 7. In VA or SKL, the resulting N-contents at pH 7 corresponded to a 76 or 62 mol% of the theory, respectively, i.e. based on the available C5 positions in phenolic guaiacyl units (G-units). In the case of SKL, 31P-NMR analysis confirmed a 77% conversion of all phenolic G-units into their C5 substituted derivatives. The Mannich reaction should be performed on lignin at pH 7 for 1 h to suppress unwanted side reactions, which could be observed by LC-MS under other pH conditions. The reaction is suitable for fast and reliable determination of reactive C5-positions in lignin by multiplication of the N-content of the reaction products with a factor of 1.6.

Emneord
Amination, Chemical reactions, Formaldehyde, Liquid chromatography, Mass spectrometry, Nitrogen, Organic polymers, Reaction products, Reactivity (nuclear)
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-28194 (URN)10.1515/hf-2016-0054 (DOI)2-s2.0-85008709552 (Scopus ID)
Merknad

cited By 0

Tilgjengelig fra: 2017-02-16 Laget: 2017-02-16 Sist oppdatert: 2018-08-22bibliografisk kontrollert
Sjöholm, E., Törngren, P. & Rönnols, J. (2017). Microwave assisted etherification of lignin. In: International symposium on green chemistry (ISGC 2017), May 16-19, 2017, La Rochelle, France: . Paper presented at International symposium on green chemistry (ISGC 2017), May 16-19, 2017, La Rochelle, France. , Article ID 1271.
Åpne denne publikasjonen i ny fane eller vindu >>Microwave assisted etherification of lignin
2017 (engelsk)Inngår i: International symposium on green chemistry (ISGC 2017), May 16-19, 2017, La Rochelle, France, 2017, artikkel-id 1271Konferansepaper, Poster (with or without abstract) (Annet vitenskapelig)
Abstract [en]

The content of phenol and aliphatic groups of softwood kraft lignin has been altered to control the reactivity and the physical properties of the lignin. The influence of microwave assisted alkylation was evaluated using dimethyl carbonate (DMC) or diethyl carbonate (DEC) together with different bases. The influence of reaction conditions on the final lignin products were compared by NMR.

Emneord
lignin, carbonate, alkylation
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-33022 (URN)
Konferanse
International symposium on green chemistry (ISGC 2017), May 16-19, 2017, La Rochelle, France
Tilgjengelig fra: 2018-01-10 Laget: 2018-01-10 Sist oppdatert: 2018-08-21bibliografisk kontrollert
Olsson, C., Hagström, B., Sjöholm, E. & Reimann, A. (2015). Carbon fibres from lignin-cellulose precursor. In: 18th International Symposium on Wood, Fiber and Pulping Chemistry, September 9-11, 2015, Vienna: . Paper presented at 18th International Symposium on Wood, Fiber and Pulping Chemistry, September 9-11, 2015, Vienna (pp. 126-129). , Poster
Åpne denne publikasjonen i ny fane eller vindu >>Carbon fibres from lignin-cellulose precursor
2015 (engelsk)Inngår i: 18th International Symposium on Wood, Fiber and Pulping Chemistry, September 9-11, 2015, Vienna, 2015, Vol. Poster, s. 126-129Konferansepaper, Poster (with or without abstract) (Annet vitenskapelig)
Abstract [en]

A series of two-component precursor fibres for carbon fibre production has been produced by air-gap spinning of kraft lignin with cellulose as the fibreforming polymer, the latter from paper grade or dissolving grade pulps. The spun precursor fibres,containing 70% lignin and 30% cellulose, demonstrate mechanical properties equivalent to commercial textile fibres. Precursor fibres based on softwood kraft lignin were treated thermally in twosteps to carbon fibres, which had mechanical properties equal to or greater than those reported for neat lignin-based carbon fibres produced by melt spinning. An advantage of the wet-spun precursor fibres developed in this project is that they are more flexible and easier to handle with a decreased risk ofbrittle fracture. The potential for further improvement for the new type of carbon fibre is very high.

Emneord
cellulose fibre, lignin, wet spinning, carbon fibre, precursor
HSV kategori
Identifikatorer
urn:nbn:se:ri:diva-29123 (URN)
Konferanse
18th International Symposium on Wood, Fiber and Pulping Chemistry, September 9-11, 2015, Vienna
Tilgjengelig fra: 2017-03-20 Laget: 2017-03-20 Sist oppdatert: 2019-06-28bibliografisk kontrollert
Identifikatorer
ORCID-id: ORCID iD iconorcid.org/0000-0002-4858-7352
v. 2.35.7